Manual.ly Logo

Dremel Stylo+ 2050 Uputstvo-Za-Upotrebu

4,0 · 4 Ocene

PDF uputstvo · 164 Stranica

српски

M: GO-GEM-FL-25
stranica

/ 164

Loading...
9c8eef9c2a66ff041a179419530e90183af9 page 9
SAFETY INSTRUCTIONS FOR
ALL OPERATIONS
SAFETY WARNINGS COMMON FOR GRINDING,
SANDING, WIRE BRUSHING, POLISHING, CARVING OR
ABRASIVE CUTTING-OFF OPERATIONS
a. This power tool is intended to function as a grinder,
sander, wire brush, polisher, carving or cut-off tool.
Read all safety warnings, instructions, illustrations

Failure to follow all instructions listed below may result
in electric shock, re and/or serious injury.
b. 
designed and recommended by the tool
manufacturer. Just because the accessory can be
attached to your power tool, it does not assure safe
operation.
c. The rated speed of the grinding accessories must
be at least equal to the maximum speed marked on
the power tool. Grinding accessories running faster
than their rated speed can break and y apart.
d. The outside diameter and the thickness of your
accessory must be within the capacity rating of
your power tool. Incorrectly sized accessories cannot
be adequately controlled.
e. The arbour size of wheels, sanding drums or any

collet of the power tool. Accessories that do not
match the mounting hardware of the power tool will run
out of balance, vibrate excessively and may cause loss
of control.
f. Mandrel mounted wheels, sanding drums, cutters
or other accessories must be fully inserted into
the collet or chuck. If the mandrel is insufciently
held and/or the overhang of the wheel is too long, the
mounted wheel may become loose and be ejected at
high velocity.
g. Do not use a damaged accessory. Before each use
inspect the accessory such as abrasive wheels for
chips and cracks, sanding drum for cracks, tear or
excess wear, wire brush for loose or cracked wires.
If power tool or accessory is dropped, inspect for
damage or install an undamaged accessory. After
inspecting and installing an accessory, position
yourself and bystanders away from the plane of
the rotating accessory and run the power tool at
maximum no-load speed for one minute. Damaged
accessories will normally break apart during this test time.
h. Wear personal protective equipment. Depending
on application, use face shield, safety goggles or
safety glasses. As appropriate, wear dust mask,
hearing protectors, gloves and workshop apron
capable of stopping small abrasive or workpiece
fragments. The eye protection must be capable of
stopping ying debris generated by various operations.
The dust mask or respirator must be capable of
ltrating particles generated by your operation.
Prolonged exposure to high intensity noise may cause
hearing loss.
i. Keep bystanders a safe distance away from work
area. Anyone entering the work area must wear
personal protective equipment. Fragments of
workpiece or of a broken accessory may y away and
cause injury beyond immediate area of operation.
j. Hold power tool by insulated gripping surfaces
only, when performing an operation where the
cutting accessory may contact hidden wiring or its
own cord. Cutting accessory contacting a “live” wire
may make exposed metal parts of the power tool “live”
and could give the operator an electric shock.
k. 
the start-up. The reaction torque of the motor, as it
accelerates to full speed, can cause the tool to twist.
l. Use clamps to support workpiece whenever
practical. Never hold a small workpiece in one
hand and the tool in the other hand while in use.
Clamping a small workpiece allows you to use your
hand(s) to control the tool. Round material such as
dowel rods, pipes or tubing have a tendency to roll
while being cut, and may cause the bit to bind or jump
toward you.
m. Position the cord clear of the spinning accessory.
If you lose control, the cord may be cut or snagged
and your hand or arm may be pulled into the spinning
accessory.
n. Never lay the power tool down until the accessory
has come to a complete stop. The spinning
accessory may grab the surface and pull the power
tool out of your control.
o. After changing the bits or making any adjustments,
make sure the collet nut, chuck or any other
adjustment devices are securely tightened. Loose
adjustment devices can unexpectedly shift, causing
loss of control, loose rotating components will be
violently thrown.
p. Do not run the power tool while carrying it at your
side. Accidental contact with the spinning accessory
could snag your clothing, pulling the accessory into
your body.
q. Regularly clean the power tool’s air vents. The
motor’s fan will draw the dust inside the housing and
excessive accumulation of powdered metal may cause
electrical hazards.
r. 
materials. Sparks could ignite these materials.
s. Do not use accessories that require liquid coolants.
Using water or other liquid coolants may result in
electrocution or shock.
KICKBACK AND RELATED WARNINGS
Kickback is a sudden reaction to a pinched or snagged
rotating wheel, sanding band, brush or any other
accessory. Pinching or snagging causes rapid stalling
of the rotating accessory which in turn causes the
uncontrolled power tool to be forced in the direction
opposite of the accessory’s rotation.
For example, if an abrasive wheel is snagged or pinched
by the workpiece, the edge of the wheel that is entering
into the pinch point can dig into the surface of the material
causing the wheel to climb out or kick out. The wheel may
either jump toward or away from the operator, depending on
direction of the wheel’s movement at the point of pinching.
Abrasive wheels may also break under these conditions.
Kickback is the result of power tool misuse and/or incorrect
operating procedures or conditions and can be avoided by
taking proper precautions as given below.
a. 
your body and arm to allow you to resist kickback
forces. The operator can control kickback forces, if
proper precautions are taken.
b. Use special care when working corners, sharp
edges etc. Avoid bouncing and snagging the
accessory. Corners, sharp edges or bouncing have
a tendency to snag the rotating accessory and cause
loss of control or kickback.
c. Do not attach a toothed saw blade. Such blades
create frequent kickback and loss of control.
d. Always feed the bit into the material in the same
direction as the cutting edge is exiting from the
material (which is the same direction as the chips
are thrown). Feeding the tool in the wrong direction
causes the cutting edge of the bit to climb out of the
work and pull the tool in the direction of this feed.
9

Razgovarajte sa svojim Dremel Stylo+ 2050 uputstvom koristeći AI

Dobijte trenutne AI odgovore iz svog Dremel Stylo+ 2050 uputstva

Pitajte bilo šta o Dremel Stylo+ 2050. Odgovori dolaze iz ovog priručnika, uz strane na kojima se zasnivaju.

Stylo+ 2050 Raspored odrzavanja

Redovno
Oistite otvore za ventilaciju i poluge prekidača

Održavajte otvore za ventilaciju i poluge prekidača čistima i bez stranog materijala koristeći suvi kompresovani vazduh. Ne ubacujte oštre predmete.

Prikazi u uputstvu (stranica 12)
Pre svake upotrebe
Proverite opremu na oštećenja

Pre svake operacije proverite brusne krugove na ogrebotine i pukotine, bubnjeve za brušenje na suze ili habanje, i žičane četke na labave žice.

Prikazi u uputstvu (stranica 9)
M: QW-35-FL

Pitajte Pitanje

0/1000

Da li preporučujete Stylo+ 2050?

Da Ne
0
User Pic

Benoît Hamel

pre 8 meseci

Smatram da je dugme za zaključavanje stezne glave nezgodno. Kada isključujem, slučajno ga pritisnem zajedno sa dugmetom za napajanje i čuje se škripav zvuk. Da li je to normalno i kako mogu to da sprečim?

0
User Pic

Manual.ly

pre 8 meseci

Prekidač za blokadu stezne glave je postavljen naspram dugmeta za napajanje, tako da pritiskanje oba istovremeno može izazvati kratak mehanički zvuk. Da biste to sprečili, uverite se da blokada stezne glave nije aktivirana kada isključujete uređaj: prvo isključite napajanje, a zatim drugom rukom otpustite blokadu (ili nakratko zastanite kako vam prsti ne bi bili na oba dugmeta). Nakon toga, nastavite sa normalnim radom. Ako se zvuk nastavlja čak i kada pazite da ne pritisnete oba dugmeta istovremeno, pokušajte da očistite oko područja prekidača i proverite da li ima vidljivih prepreka. Ako i dalje postoji, molimo vas da kontaktirate podršku sa kratkim videom kako bismo mogli da pregledamo uređaj.

M: OA-GPT-5-NAN
M: OA-GPT-5-NAN

Често постављана Питања

A

Најбољи је за детаљне задатке као што су гравирање, полирање, брушење, резбарење, чишћење и лагано сечење. Његов танак облик је посебно користан када је прецизност важнија од снаге.

Да ли је овај одговор користан?

A

Да, ова верзија долази са додацима, што је чини спремном за разне мање пројекте. Укључени алати проширују употребу изван основне брусилице и подржавају креативније примене.

Да ли је овај одговор користан?

A

Да. Алат има контролу променљиве брзине, па можете прилагодити перформансе материјалу и задатку. Ниже брзине су корисне за полирање, а више за тврђе материјале.

Да ли је овај одговор користан?

A

Да. Његов сужени дизајн налик оловци направљен је за контролу и удобност. Природно лежи у руци и идеалан је за фине, вођене покрете по малим површинама.

Да ли је овај одговор користан?

A

Користите одговарајућу заштиту за очи и од прашине, избегавајте претеран притисак и уверите се да су додаци сигурно постављени. Такође изаберите одговарајућу брзину за материјал како бисте спречили оштећења.

Да ли је овај одговор користан?

A

Боље је прилагођен прецизном и лакшем раду него тешком брушењу. За захтевно уклањање материјала бољи избор био би већи и снажнији алат.

Да ли је овај одговор користан?

M: GO-GEM-FL-25

Prednosti i Nedostaci

Prednosti

  • Танак хват у стилу оловке олакшава и чини удобнијим детаљан рад.
  • Контрола променљиве брзине помаже прилагођавању различитим материјалима и задацима.
  • Компатибилан је са више додатака за полирање, резбарење, брушење и гравирање.
  • Лагана конструкција смањује замор током дужих пројеката.
VS

Nedostaci

  • Није идеалан за тешко брушење или агресивно уклањање материјала.
  • Најбољи резултати захтевају пажљив избор брзине и лаган додир.
  • Неким додацима може бити потребно мало вежбе да би се правилно монтирали и избалансирали.
  • Прашина, бука и мере безбедности су и даље важни током употребе.
M: GO-GEM-FL-25

Proizvod Specifikacija

Tip

Prava brusilica

Snaga

9W (230V)

Brzina bez opterećenja

5.000-22.000/min

Drška alata

0,8-3,2 mm brzostezna glava, čaura

Posebne karakteristike

Regulacija brzine

Težina

110 g

Obim isporuke

Set pribora od 15 delova

M: GO-GEM-FL-25

Proizvod Opis

Dremel Stylo+ електрична права брусилица са додацима (2050-15)

Dremel Stylo+ електрична права брусилица је дизајнирана за људе који желе прецизност у танком, лаком за држање формату. Њено кућиште налик оловци чини да природно лежи у руци, што је посебно корисно за детаљан рад који захтева контролу, а не сирову снагу. Уз укључене додатке, овај компактни алат постаје свестран пратилац за полирање, чишћење, резбарење, брушење, гравирање и лагано сечење.

Мали алат са великом свестраношћу

Једна од најпривлачнијих ствари код Stylo+ модела јесте колико је приступачан за употребу. Уместо гломазног кућишта, нуди сужени облик који подржава фине, вођене покрете. То га чини паметним избором за хоби пројекте, завршну обраду рукотворина, рад на моделима и деликатне поправке. Контрола променљиве брзине додаје још један ниво корисности, омогућавајући вам да прилагодите алат материјалу и задатку.

Направљен за детаљан рад

Укључено упутство наглашава правилан избор брзине и безбедно руковање, што много говори о намени алата: направљен је да пружи најбоље резултате када се користи лаганим додиром. Брусилица ради са широким избором Dremel додатака, а систем стезне главе помаже да замена додатака буде бржа и лакша. За кориснике који желе прецизније стезање, доступан је и систем чаура. Та флексибилност је права предност када прелазите са полирног филца на брусне бубњеве, секаче или сврдла за гравирање.

Практичне перформансе у свакодневној употреби

У основи, Stylo+ је ту због удобности и контроле. Лаган је, лак за маневрисање и погодан за дуге сесије у којима је замор шаке важан фактор. Опсег брзине алата помаже да се усклади са обрадком: ниже брзине су боље за полирање и осетљиве материјале, док су више брзине погодне за дрво, метал, стакло и обликовање. Због тога је поуздан избор за креаторе који раде на различитим површинама и техниками.

Безбедност и одржавање су важни

Као и сваки ротациони алат, Stylo+ најбоље функционише уз пажљиву употребу. Упутство истиче заштитне наочаре, заштиту од прашине и правилно постављање додатака као основне елементе. Такође подсећа кориснике да избегавају претеран притисак, јер је алат направљен тако да додатак обавља посао. Редовно чишћење и правилно одлагање помоћи ће да алат дуго ради глатко.

Напомене

  • Најбољи резултати се постижу избором правог додатка и брзине.
  • Нежан додир побољшава прецизност и смањује хабање.
  • Користите одговарајућу заштиту када може доћи до прашине или варница.

Укратко, Dremel Stylo+ је уредно решење за пројекте усмерене на прецизност. Комбинује преносивост, контролу и флексибилност додатака у формату који је веома погодан за детаљан креативни рад.

M: GO-GEM-FL-25

© Copyright 2026 Manual.ly